9. 100 T, 2×In-Fusion Cloning Mix Plus, $1200

Product Information

Description

This product 2×In-Fusion Cloning Mix Plus is an upgraded product of 2×In-Fusion Cloning Mix (G3350). 2×In-Fusion Cloning Mix Plus is compatible with single or 2~5 multi-fragment directional recombination into the vector. Its principle is to linearize the vector first, and then introduce the end sequence of the linearized vector into the 5′ end of the forward/reverse amplification primer of the DNA fragment inserted into the linearized vector, so that the 5′ and 3′ ends of the PCR amplification product are Each has a sequence (15-25 bp) identical to the end of the linearized vector. In the 2×In-Fusion Cloning Mix master mix, it is necessary to mix the PCR product and the linearized vector with sequences consistent with the ends of the linearized vector in a certain proportion, and then incubate it on ice (or in ice water mixture) for 5 min. Then, transformation of competent cells can be performed and directed cloning can be accomplished.

The upgraded 2×In-Fusion Cloning Mix Plus significantly improves the recombination efficiency of clones. For the construction of single-segment DNA recombinant plasmids, the proportion of positive clones obtained by using this premix is as high as 99%; for the construction of 2-5 multi-segment DNA recombinant plasmids, the proportion of positive clones obtained by using this premix is as high as 90% . The simultaneous insertion of multiple fragments greatly simplifies the experimental steps, improves efficiency and saves time.

Storage and Handling Conditions

Transported with wet ice; stored at -20°C, valid for 12 months.

Component

Assay Protocol

Ligation system (recommended 10 μL reaction system)

1. For single-fragment recombination reactions, it is recommended to place in 50°C water for 15 minutes, and then place on ice to cool immediately.

2. For the multi-fragment recombination reaction, it is recommended to keep it in 50°C water for 30 minutes, and then immediately place it on ice to cool (for 3-5 multi-fragment recombination, it is effective to extend the recombination time appropriately to improve the recombination efficiency, but the most length should not exceed 1 h).

Reaction product conversion

1. Take out the competent cells (such as E.coli DH5α, E.coli Top10, etc.) from the -80℃ refrigerator and place them on ice to thaw.

2. Add the reacted sample to the competent state, gently move the bottom of the tube with your fingers to mix well, and take an ice bath for 30 minutes.

3. The product was then placed in a water bath at 42°C and heat-shocked for 90 s. After that, it was quickly placed on ice for 2-5 minutes.

4. Take 900 μL of sterile SOC or LB medium and add it to the EP tube. After mixing, place the EP tube on a shaker and incubate at 220 rpm at 37°C for 1 h to recover the bacteria (it can also be cultured in a 37°C incubator for 1 h);

5. According to the experimental requirements, draw different volumes of transformed competent cells and add them to LB solid medium containing corresponding antibiotics, spread the cells evenly, and after the liquid is completely absorbed, place the plate upside down in a 37°C incubator and culture overnight.

Positive clone identification

The monoclonal colonies grown on the plates are picked for colony PCR identification, or after culturing, the plasmids are extracted for digestion or PCR identification, or the extracted plasmids are directly sequenced and identified.

Note:

1. The vector and target fragments must be gel purified and their quality and concentration detected by electrophoresis. Water can be omitted when the concentration is low.

2. The Tm value between the overlapping regions of multiple fragments should be consistent and >60℃.

3. It is recommended that the molar ratio of vector and insert is 1:1~1:3; when 2-3 fragments are connected, the molar ratio between each fragment is 1:1, and the ligation efficiency of 2-3 fragments will decrease. The ligation reaction system can be scaled up in equal proportions.

4. When the total volume of vector and insert is greater than 5 μL, the reaction system can be scaled up to 20 μL.

5. The volume of the ligation product should not exceed 1/10 of the volume of the competent cells, otherwise the transformation efficiency will be significantly reduced. The volume of the ligation product and the competent cells can be increased in equal proportions (for example, 20 μL of ligation system transforms 200 μL of competent cells).

6. It is recommended to take out the 2×In-Fusion Cloning Mix before use, and put it back to -20°C immediately after use. It can be frozen in aliquots to reduce repeated freeze-thaw cycles.

7. When electroporation is used for transformation, the reaction product needs to be purified by column method or ethanol precipitation method.

For Research Use Only!

Ver. No.: V1.0-202111