6. MTT Cell Proliferation and Cytotoxicity Assay Kit, 100 T $99 (MTT Cell Proliferation and Cytotoxicity Assay Kit)
Description
Product Information
Product Name | Cat.No. | Spec. |
MTT Cell Viability Assay | G4104-100T | 100T |
G4104-500T | 500T |
Description/Introduction
MTT is also called 3-(4,5-dimethyl-2-thiazolyl)-2,5-diphenyl-2-H-tetrazolium bromide (Thiazolyl Blue Tetrazolium Bromide). Its molecular formula is C18H16BrN5S, and the molecular weight is 414.32.
The MTT Cell Viability Assay utilizes the well-established and widely used MTT reagent to determine mammalian cell viability. The redox potential in active mammalian cells reduces MTT to a strongly pigmented formazan product. After solubilization, the absorbance of the formazan can be measured with a microplate absorbance reader. The MTT Cell Viability Assay is a complete, optimized kit that provides all the reagents necessary for the detection of mammalian cell viability.
The redox potential in viable mammalian cells causes the water soluble MTT reagent (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) to convert to an insoluble formazan product. After solubilization of the formazan with the included SDS (sodium dodecyl sulfate) reagent, the concentration of the colorimetric probe is determined by an optical density measurement at 570 nm.
The MTT Cell Viability Assay provides a simple method for determination of mammalian cell viability using standard microplate absorbance readers. Simply prepare the MTT reagent, add it to the cells, solubilize the resulting formazan, and determine the optical density using a standard microplate reader.
Storage and Handling Conditions
Transport in wet ice; MTT solution, -20°C, protect from light; formazan dissolving agent, 4°C, protect from light; valid for 12 months.
Component
Component Number | Component | G4104-100T | G4104-500T |
G4104-1 | MTT Solution | 1 mL | 5×1 mL |
G4104-2 | Formazan Dissolving Agent | 10 mL | 50 mL |
Protocol | 1 |
Assay Protocol / Procedures
1. For cell proliferation assay, it is recommended to seed 100 μL of 2000 cells per well; for cytotoxicity experiments, it is recommended to seed 100 μL of 5000 cells per well (depending on cell size and proliferation rate). Culture and transfection or drug pretreatment according to the needs of the experiment;
2. Add 10 μL of MTT solution to each well and incubate for 4 h in an incubator;
3. a. Add 100 μL of formazan dissolving agent to the well plate,
b. tap the well plate to mix evenly
c. incubate in the incubator for 2-4 hours to dissolve the formazan (the incubation time depends on the number of cells)
4. Measure the absorbance of each well at 570 nm. If 570 nm filter is not available, the 560-600 nm filter can be used instead.
Note:
1. Use a 96-well plate for detection. If the cell culture time is long, it should be pay attention to the problem of evaporation. The circle around the 96-well plate is the easiest to evaporate. You can discard the circle and add PBS, water or culture medium instead. You can also ease the evaporation by placing the 96-well plate near the water source in the incubator.
2. In order to reduce the error caused by the experimental operation, it is recommended to set up duplicate wells to avoid the generation of air bubbles when adding samples or shaking and mixing.
3. The MTT solution is yellow. Before use, it should be placed at room temperature in the dark and water bath at 20-25°C for a while until it is completely melted before use. Prolonged exposure to light will cause failure, do not use if the solution is grey green.
4. If the formazan dissolving agent is precipitated, it can be dissolved in a water bath at room temperature or 37°C to promote dissolution, and then it can be used after dissolving and mixing.
5. For your health and safety, please wear a lab coat and disposable gloves when operating.
For Research Use Only!
Cat.No.
|
Product Name
|
Spec.
|
Operation
|
---|
G1601
|
Click-iT EdU-488 Cell Proliferation Detection Kit
|
100 T
|
|
G1602
|
Click-iT EdU-555 Cell Proliferation Assay Kit
|
100 T
|
|
G1603
|
Click-iT EdU-594 Cell Proliferation Assay Kit
|
100 T
|
|
G1604
|
Click-iT EdU-647 Cell Proliferation Assay Kit
|
100 T
|
|
G1609-100T
|
Calcein AM Cell Viability Assay Kit
|
100 T
|
|
G1609-500T
|
Calcein AM Cell Viability Assay Kit
|
500 T
|
|
G1610-100T
|
LDH Cytotoxicity Assay Kit
|
100 T
|
|
G1707-100T
|
Servicebio® Calcein-AM/PI Living / Dead cell Double Staining Kit
|
100 T
|
|
G4101-1000T
|
MTT Cell Viability Assay Kit
|
1000 T
|
|
G4101-200T
|
MTT Cell Viability Assay Kit
|
200 T
|
|
G4102-100T
|
Brdu Detection Kit
|
100 μL+30 mL×4
|
|
G4102-50T
|
Brdu Detection Kit
|
50 μL+30 mL×4
|
|
G4103-1ML
|
Cell Counting Kit-8
|
1 mL (100T)
|
|
G4103-5ML
|
Cell Counting Kit-8
|
5 mL (500T)
|
|
G4104-100T
|
MTT Cell Proliferation and Cytotoxicity Assay Kit
|
100 T
|
|
G4104-500T
|
MTT Cell Proliferation and Cytotoxicity Assay Kit
|
500 T
|
|
G5059-100MG
|
EdU (5-Ethyl-2′-deoxyuridine)
|
100 mg
|